ADEMCO 5817 PDF

Honeywell Security Intrusion and Communications, ADEMCO, AlarmNet, IntelliSense, Apex, FBII, electronic security systems, burglary alarms and fire alarms for. Installation manual for the Honeywell wireless three-zone sensor. For help installing your , call The Honeywell is a wireless three zone sensor. Unlike other Honeywell wireless window and door sensors, the does not have an internal reed switch.

Author: Moshicage Akinogor
Country: Dominica
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 March 2007
Pages: 314
PDF File Size: 13.62 Mb
ePub File Size: 14.2 Mb
ISBN: 410-9-67528-621-5
Downloads: 11780
Price: Free* [*Free Regsitration Required]
Uploader: Gardanos

Got it, continue to print. Regular maintenance and inspection at least annually by the installer and frequent testing by. Disengage the supplied mounting plate from the unit by inserting the blade of a small. If concealed wiring is to be used, feed the wires through the concealed wiring entry hole at.

Afemco the transmitter is being enrolled by the control, all DIP switch positions should.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product s. To replace the cover, engage the hooks along one edge and snap shut.

Replace battery only with: Dispose of used batteries promptly. The locking tab ademdo click as the case back locks in place. Disengage the supplied mounting plate from the unit by inserting the blade of a small screwdriver into the locking tab release window see Diagram 2 and pressing it against the case locking tab see Diagram 1 while sliding the plate downward along the case back.

Install the mounting plate, with its case holding posts pointing up in this examplein the. The unit may, however, be installed in any direction, as long as the relationship of the unit to its mounting plate is maintained. Recommendations must be included for a specific. Attach the case back to the mounting plate by sliding the keyhole slots in the case back down.

  AMERICAN DYNAMICS CC300 PDF

Surface wiring should enter via the thin “breakout” area provided in.

It is not necessary to program the transmitter IDs during installation. Do not recharge, disassemble, heat above. Seller shall have no obligation under ademcoo Limited Warranty or otherwise if the product s is altered or improperly repaired or serviced by anyone other than Honeywell factory service.

Remove the transmitter’s cover if not already off as described in Mounting Step 1. Add to my manuals Add. The has its own axemco identification codes permanently assigned during manufacture. A built-in cover tamper switch is activated when the cover is removed. The Multi-Point Universal Transmitter may have three contact loops connected to it.

When a satisfactory location is found, remove the battery and proceed with installation. Except in the case of the position 4 ON setting, the Auxiliary loops are not affected by.

Honeywell ADEMCO User Manual | 2 pages

The two Auxiliary Loops are closed-circuit, with a nominal response time of mSec. Seller’s obligation shall be limited 517 repairing or replacing, at its option, free of charge for materials or labor, any product s which is proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under normal use and service. The Primary Loop has several DIP switch selectable options that determine its connection requirements, response, and transmission characteristics see DIP switch setting table on next page.

Comments to this Manuals Your Name. For this application, the alignment guide strip along one edge of the plate serves no function and may be broken away, if desired. The description that follows assumes that the unit will be mounted as shown in the diagrams.

If a acemco loop is not to be used, no connection is needed across its terminals. Seller does not represent that the product s it sells may not be compromised or circumvented; that the product s will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product s will in all cases provide adequate warning or protection. Don’t have an account?

  LIVRO SHIGEO SHINGO PDF

If concealed wiring is to be used, feed it through the slot in the case back but do not connect. For UL installations with fire zones, the position 4 ON setting must not be used. Each loop transmits aremco unique ID code to a wireless system receiver connected to the system control panel.

Mounting For proper orientation of the unit in relation to its wall mounting plate and the loop wiring, read all of this section before installing the unit. To print the manual completely, please, download it.

Don’t show me this message again. Risk of fire, explosion, and burns.

Honeywell ADEMCO 5817 User Manual

Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fireor other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. The should be admeco as “RF” i. By pressing ‘print’ button asemco will print only current page.

Page of 2 Go. The installer should assume the responsibility of developing and offering a regular maintenance.

Honeywell ADEMCO 5817 3 Point Wireless Transmiter

For UL installations, no contact in any of the loops may be more than 3 feet from the transmitter. Enter text from picture: Complain wrong Brand wrong Model non readable.

zdemco

Observe correct polarity and insert the battery provided into the battery holder see. No increase or alteration, written or verbal, of the obligations of this 5871 Warranty is authorized.