ASTM E112 PDF

ASTM E methods for grain counting using microscope reticle. ASTM E GRAIN SIZE MEASURING METHODS, metallurgy, american society for testing and materials. ASTM E standard is commonly practiced within the United States for determining the quality of a specific alloy. This standard is routinely performed by .

Author: Tygolkree Disho
Country: Gambia
Language: English (Spanish)
Genre: Life
Published (Last): 25 April 2007
Pages: 403
PDF File Size: 9.73 Mb
ePub File Size: 13.93 Mb
ISBN: 271-8-83160-460-7
Downloads: 49950
Price: Free* [*Free Regsitration Required]
Uploader: Bagore

These test methods may also be applied to nonmetallic materials with structures having appearances similar to those of the metallic structures shown in the comparison charts.

ASTM E112 Grain Size Examination

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Historical Version s – view previous versions of standard. These test methods apply chiefly to single phase grain structures but they can be applied to determine the average size of a particular type of grain structure in a multiphase or multiconstituent specimen.

Heyn Linear Intercept Procedure. These test methods may also be applied to nonmetallic materials with structures having appearances similar to those of the metallic structures shown in the comparison charts. The grain size of specimens e12 two phases, or a phase and a constituent, can be measured using a combination of two methods, a measurement of the volume fraction of the phase and an intercept or planimetric count see Section Characterization of grain size in specimens with sstm grain e12 distributions is described in Test Methods E It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to ee112.

Determination of spatial grain size, that is, measurement of the size of the three-dimensional grains in the specimen volume, is beyond the scope of these test methods.

  ASTM A262-13 PDF

Equivalent inch-pound values, when listed, are in parentheses and may be approximate. An accurate count does require marking off of the grains as they are counted. Application to Special Situations. Fracture Grain Size Method. The three basic procedures for grain size estimation are: The test methods may also be used for any structures having appearances astn to those of the metallic structures shown in the comparison charts.

The intercept procedure is particularly useful for structures consisting of elongated grains see Section For higher degrees of accuracy in determining average grain size, the intercept or planimetric procedures may be used. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Characterization of grain size in specimens with duplex grain size distributions is described in Test Methods E These test methods do not cover methods to characterize the nature of these distributions. These distributions are approximately log normal. The three basic procedures for grain size estimation are:.

Grain Size Examination – ASTM E Grain Size Analysis | SGS MSi Testing

Heyn Linear Intercept Procedure. Because they show a distribution of grain dimensions, ranging from very small to very large, depending on the relationship of the planar section and the three-dimensional array of grains, the charts are not applicable to measurement of individual grains. Link to Active This link will always route to the current Active version of the standard. Results of Interlaboratory Grain Size Determinations.

Measurement of individual, very coarse grains in a fine grained matrix is described in Test Methods E Determination of spatial grain size, that is, measurement of the size of the three-dimensional grains in the specimen volume, is beyond the scope of these test methods. These distributions are approximately log normal.

Partially recrystallized wrought alloys and lightly to moderately cold-worked material may be considered as consisting of non-equiaxed grains, if a grain size measurement is necessary. Application axtm Special Situations.

  ANTENNA ENGINEERING HANDBOOK VOLAKIS PDF

Utilization of semi-automatic digitizing tablets or automatic image analyzers to measure grain size is described in Test Methods E The precision of the w112 is a function of the number of intercepts or intersections counted. These charts were constructed to reflect the typical log-normal distribution of grain sizes that result when a plane is passed through a three-dimensional array of grains.

Active view current version of standard. Specimens with Non-equiaxed Grain Shapes. Fracture Grain Size Method. Link to Active This link will always route to the current Active version of the standard. Equivalent inch-pound values, when listed, are in parentheses and may be approximate. Specimens with Non-equiaxed Grain Shapes.

These test methods do not cover methods to characterize the nature of these distributions. Historical Version s – view previous versions of standard Translated Version s: Results of Interlaboratory Grain Size Determinations. Utilization of semi-automatic digitizing tablets or automatic image analyzers to measure grain size is described in Test Methods E Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Measurement of individual, very coarse grains in a fine grained matrix is described in Test Methods E The precision of the method is a function of the number of grains counted.

Because an accurate count can be made without need of marking off intercepts or intersections, the intercept method is faster than the planimetric method for the same level of precision. These test methods apply chiefly to single phase grain structures but they can be applied to determine the average size of a particular type of grain structure in a multiphase or multiconstituent specimen.