CEI EN 50160 PDF

EN Caratteristiche della tensione fornita dalle reti pubbliche di distribuzione utilizzare un registratore conforme alla CEI EN In questo. Power quality has many meanings depending on what the power is used for. • Measuring PQ is all about deviations from normal state. • USERS. of European Norm Some countries have used EN as the basis for their national quality of supply regulations. But the standard’s statistical models.

Author: Felabar Kiganris
Country: Papua New Guinea
Language: English (Spanish)
Genre: Science
Published (Last): 11 October 2016
Pages: 159
PDF File Size: 3.9 Mb
ePub File Size: 7.22 Mb
ISBN: 615-9-40371-125-6
Downloads: 23431
Price: Free* [*Free Regsitration Required]
Uploader: Daijas

The effects of voltage sags are the malfunction of the devices connected to the network or the termination of the operation, depending on the extent of the event, in terms of depth and duration, and the ceo of susceptibility of loads.

The project is related to the development of a sensors’ wn to measure Power Quality with the ability to connect it both wirelessly and by wiringfor the analysis of a low-voltage grid.

It shows a test regarding measurement GUM. A study direction is This paper refers to these measurement issues related to represented by the analysis of physical phenomena that lead calibration of power quality analyzers and present to alterations in parameters of voltage and current in AC experimental results for some of the parameters related to the networks [1], [2]. A second possibility is to place the devices on a wired network, this allows you to overcome the problems related to the distances of the measuring points, but this second solution requires an existing network or the ability to create 5060 with an increase in costs which is non-negligible.

This single device realizes the SPQ block of the network shown in Fig. The sags may affect one or more stages depending on the phenomena that cause them. Non-Sinusoidal Voltage — Testing state 2 [5] A. The router is a device consisting only of much smaller processor that dn the ZigBee protocol and the Dei card. Machines, Elsevier Academic Press, [4] J.

This will give you a positive deflection of the trend of Q. Mechatronics,p. All voltage values outside these tolerances do not correspond to GOST and can be hazardous to appliances and equipment in one form or another. The starting method is the study of the flow of reactive power [9].

  ISO 5725-5 PDF

Aspects of metrological calibration of power quality analyzers | George Seritan –

The following are the basic steps of the algorithm. One of the objectives pursued in the design was to obtain the flexibility of the module, in order to be used for different measurements. The serial communication to the PC is made possible according to the standard that describes the RS specifications.

This happens for example in managing actions, and currency exchange. Baggini, Power Quality Tutorial, Leonardo Energy,The methodology used in this situation is similar in non- www.

Cei En Pdf 14 · GitBook (Legacy)

Tecniche di prova e di misura – Metodi di misura della qualita della potenza. The following are the most interesting values Table 2.

The RDF node for measuring basic parameters of power quality which allows connecting to the central computer which can detect the direction of sag events has been developed. EEPROM to the device this requirement has already been incorporated in the target of the second prototype in development. Similarly, the failure was simulated upstream of the monitoring point. The arising mainly from the lack of clear theoretical and practical phenomenon definitions, studies of related situations and measurement specifications, both in standard as well as in measurement instruments and proposal of new standards in literature [13], [14].

Calibration can be done by one of the following procedures – select measured quantity and maintaining other [17]: The voltage stability is critical both for all those devices which for their proper functioning requires a stable operating point, as the operational amplifiers that constitute the part of signal conditioning, or regarding to the sampling, as voltage variations influence the amplitude quantization, and then the entire measurement would be altered.

If you need to store a greater amount of data, for non-real time query, you can add an external. Sinusoidal voltage — Testing state 1 the calibration for voltage magnitude the method used is The Table VI presents the results of calibration at point rms based on the use of a calibrator source. In the calculation of the line impedances the mutual impedances between the conductors have been neglected.

  ALLIED TELESIS AT-8000S PDF

CRC Press, [2] C. Here all the signal processing is performed, pre-treated and sampled at a frequency of 4 kHz, which is necessary for the study up to the 40th harmonic, as indicated by the CEI EN The presence of such harmonics on the grid is responsible for detrimental effects. In conclusion, the disturbances that affect the user depend on the characteristics of the distribution network, and on the behavior and the sensitivity of their loads. Moreover, at higher frequencies, iron losses hysteresis losses and eddy current losses as well as the losses in the cables increase.

Due to their characteristics, the input signal is faithfully reproduced, also ensuring excellent insulation from the network. In the case of upstream event, the load that caused the event will be in parallel to the load ‘victim’ which is located downstream of the monitoring point. It is possible however to define the “energy quality” as a perfect supply of it, which can ensure continuity of service, within certain tolerances of voltage and frequency, and can be characterized by a voltage with undistorted sinusoidal waveform.

New products

In the study of consumption of the smart-sensor the three phases of measurement, the processing and the transmission of the data packet were analyzed separately. Another aspect, which should not be neglected, is the resonance issue related to the presence of 550160 in electrical networks.

The purpose of the project is to create a network that can monitor systematically the power quality of cie site. Power Quality; smart sensors; low-voltage grid; EN standard; voltage sags measurement; disturbances of power quality.

Testing and measurement techniques combined cek 3rd harmonic Hz, 30V rms. Having the phase it is particularly easy to derive various values of active, reactive and apparent power.