EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . Temperature controller. EKC MAKING MODERN LIVING POSSIBLE Sensors: Danfoss Pt, PTC or NTC • Calibration of sensors. RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D.

Author: Tygoll Zulugar
Country: Estonia
Language: English (Spanish)
Genre: Business
Published (Last): 24 August 2013
Pages: 367
PDF File Size: 9.79 Mb
ePub File Size: 18.75 Mb
ISBN: 518-4-35666-901-4
Downloads: 48154
Price: Free* [*Free Regsitration Required]
Uploader: Zolomi

S5 is a defrost sensor and is used if defrost has to be stopped based on temperature. Access code 2 Access to adjustments There is access to adjustments of values, but not to configuration settings. Buttons and packing are imbedded in the front. But 120 can also use a sensor with another signal accuracy.

ON-time in minutes Min.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102D 084B8506 for Freezer

Here you define which: If the function is controlled by a signal at the DI input, the relevant status can be seen here in the menu. The limit value will also be raised in connection with reference displacement r China Good Quality Box type condenser Supplier. Dajfoss regulation will give a “Standby alarm”. None, defrost is based on time EKC A: EKC B Controller with two relay outputs, extra temperature sensor and digital input.

When the defrost starts the defrost timers are set at zero. Copying was not correct. Relays The general connections are: The controller will register when the input is reopened.


OFF-time in minutes Time delay danfosss couplings of two compressors Settings indicate the time that has to elapse from the first relay cuts in and until the next relay has to cut in. When the value is passed, canfoss defrost will start. If the settings in the controller are to be protected with an access code you can set a numerical value between 0 and However the view of —d- will be discontinued if: Push the upper or the lower button and select the new value 3.

Contact details entered above are not used to send newsletters or other advertisements. Thermostat Set point Regulation is based on the set value plus a displacement, if applicable. The function is defined in o Correction of signal from Sair Compensation possibility through long sensor cable. Time delay for cooling long alarm delay This time delay is used during start-up recovery timeduring defrost, in the cooling phase after a defrost.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC A B for Freezer

The key can contain up to 25 different sets. The value is set via a push on the 10 button. Copying still going on The information can be found in o65 or o66 a couple of seconds after copying has been started. If not, you can cancel the function with setting 0. When the input is short-circuited, there will be regulation for night operation.

Sensor error on Saux When copying settings to or from a copying key with functions o65 or o66, the following information xanfoss appear: Thermostatic Expansion Valves flow direction: Roof mounted industrial Electrical defrosting air cooler low temperature DJ series for cold room.


Operating status The controller goes through some regulating situations where it is just waiting for the next point of the regulation. Select your own number.

The controller will register when the DI input is activated. The function is furthermore only relevant if you have chosen defrost with interval start d The running times are not observed when 1022 start.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102A 084B8500 for Freezer

There is no temperature monitoring during case cleaning. Temperature signal 2 can be used for defrost stop based on temperature or for product sensor.

With only two keys, all functions can be set and programmed. China Good Quality Box type condenser Supplier. This page uses cookie files to provide its services in accordance to Cookies Usage Policy.

Controller for temperature control – EKC Manual |

The contact will cut in when the controller demands refrigeration Relay 2 Alarm. E-alarms, on the other hand, will become visible the moment the error occurs. The time delay is set in minutes.

The function can only be used in 1: Copying concluded and OK 4: And for how long it at least has to be stopped.