ECE R26 PDF

Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.

Author: Kagakinos Faukinos
Country: Philippines
Language: English (Spanish)
Genre: Automotive
Published (Last): 2 July 2016
Pages: 483
PDF File Size: 20.73 Mb
ePub File Size: 2.26 Mb
ISBN: 689-7-35256-122-5
Downloads: 43466
Price: Free* [*Free Regsitration Required]
Uploader: Digar

UN R86 Tractor Lighting. Application for Approval 4. Uniform provisions concerning the approval of motor vehicles and their components with regard to the safety- related performance of hydrogen-fuelled vehicles UN Regulation version of the HFCV Global Technical Regulation.

Any particular requirements, special fittings and so on that are specified when using the manufacturer’s replacement wheels or specific requirements for the ECE approved wheel. The surface treated sample shall pass a salt-spray test, in which the sample and any components with which is normally in contact are put in upright position into the salt-spray test equipment.

Uniform Provisions Concerning the Approval of Vehicles with regard to the Protection of the Occupants in the Event of a Lateral Collision This regulation applies to the lateral collision behavior of the structure of the passenger compartment of M1 and N1 categories of vehicles where the “R” point of the lowest seat is not more than mm from ground level when the unladen vehicle plus kg i.

In between the publication of revisions, the Secretariat may issue amendments or corrigenda to the revision corresponding to adopted proposals for new series, supplements, or corrigenda. Where original gauge length L o.

The competent authority issuing the extension of approval shall assign a series number to each communication form drawn up for such an extension. If the various clearances on the vehicle manufacturer’s replacement wheel are less than those given above, then these can be accepted.

The test documentation shall include photos showing the main corrosion points which have been mechanically washed in order to show the material defects. UN R35 Foot Controls. The normal frequency of these verifications shall be once every two efe. The requirement of Paragraph 6.

  INSTRUKCJA KOLEJOWA D19 PDF

Figures 5 and 6 show examples of the use of this procedure. The inspector may take samples at random to be tested in the manufacturer’s laboratory.

If lateral door handles rotate to operate, they shall meet one or other of the following requirements: As an exception to this requirement an exhaust pipe may project more than 10mm beyond the vertical projection of the floor line, so long as it terminates in rounded edges, the minimum radius of curvature being 2. Specimen required for approval of a separate technical unit submitted on: That department may then; 7.

Technical cracks not acceptable. When the quality level appears unsatisfactory or when it seems necessary to verify the validity of the tests carried out in the application of paragraph 8. UN R6 Direction Indicators Direction Indicators Uniform provisions concerning the approval of direction indicators for power-driven vehicles and their trailers UNECE R6 establishes technical and administrative criteria for the approval of driver-operated devices that signal a driver’s intention to change the direction in which his or her vehicle is proceeding.

These projections shall in 2r6 case satisfy the provisions of paragraph 5. Major changes ecw often include “transitional provisions” which provide dates from which compliance with the requirements becomes mandatory usually beginning with new approvals and then extending to all new products regardless of when they first received approval.

A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently. Model B See Paragraph 4. In every inspection, the test books and production survey records shall be presented to the visiting inspector. Figure 3 shows an example of the use of this procedure.

EUR-Lex Access to European Union law

Fractures and indentations caused by the direct contact with the falling weight are acceptable. Sample preparation A surface treated sample, taken from production, shall be damaged by cross engraving and stone impact ISO to represent damaging situations during the normal usage of vehicle damage shall be in the area of the rim flange and inside the wheel. UN R Cornering Lamps.

  BEKENTENISSEN VAN EEN ECONOMISCHE HUURMOORDENAAR PDF

The first two digits of the approval number indicate that, at the time of approval, Regulation No. Chapter 11 Volume P. UN R Tyre Installation. Uniform Provisions Concerning the Approval of Filament Lamps for Use in Approved Lamp Units of Power-driven Vehicles and of their Trailers UNECE R37 specifies technical and administrative requirements for the approval of a wide range of filament lamps shown in Annex 1 of the regulation that are intended for use in approved lamp units of power-driven vehicles and of their trailers.

Agricultural vehicle couplings Mechanical coupling components for agricultural vehicles UN Regulation No. EU case law Case law Digital reports Directory of case law. The regulations considers the installation and functioning of lighting equipment as a whole to ensure compatible performance across all types of equipment and devices headlamps, signalling lamps, markers lamps, etc.

This document is an excerpt from the EUR-Lex website.

EUR-Lex – X(02) – EN – EUR-Lex

Sheet-metal edges, such as gutter edges and the rails of sliding doors, shall not be permitted unless they are folded back or are fitted with a shield meeting the requirements of this Regulation which are applicable to it. Should other fixing devices be used, it is necessary prove their equivalence. R6 projections shall be determined according to the method described in paragraph 3 of Annex 3 to this Regulation.

Uniform Provisions Concerning the Approval of Advance-Warning Triangles This Regulation dce to certain advance-warning devices intended to be on board vehicles and to be placed on the carriageway in order to signal, by day and at night, the presence of a halted vehicle.

Type I — Fade test procedure. This regulation is unique in that it governs how a manufacturer may obtain a single vehicle-level approval representing compliance cee multiple UN Regulations.