INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Kagashicage Tezilkree
Country: Dominica
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 9 December 2013
Pages: 450
PDF File Size: 2.10 Mb
ePub File Size: 20.5 Mb
ISBN: 945-4-58226-228-2
Downloads: 5143
Price: Free* [*Free Regsitration Required]
Uploader: Gardadal

Premature exposure to ponding water will cause a color change, especially in dark colors. However, these phenomena are not detrimental to anti-corrosive performance. Mouse over image to zoom. Soluble salts should be removed by fresh water washing.


Accumulated dirt and soluble salts must be removed. It is also possible to apply to damp surfaces in some circumstances. NSF Certification is for tanks greater than gallons Surface preparation The performance of this product will depend upon the degree of surface preparation. However, it can be used over suitably primed surfaces.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

Please consult International Protective Coatings for alternative recommendations. The surface to be coated should be clean, dry and free from contamination. Trowel or roller can be used for small areas.


Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings. If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS.

Avoid using a mixture of application methods whenever possible. Varnish Hybrid Water base. Puddles, ponding and accumulations of water must be removed. Always mix a complete unit in the proportions supplied. Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to mds Mixing Material is supplied in two containers as a unit.

Further information is available from International Protective Coatings. In common with all epoxies Inetrseal HS will chalk and discolor on exterior exposure.

For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. Application should then msdss to a suitably primed surface.

A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Level of sheen and surface finish is dependent on application method. Once the unit has been mixed it must be used within the working pot life specified.


Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. Certification is for tanks greater than gallons However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used.


Prior to paint application all surfaces should be assessed and treated in accordance with ISO With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Loose or flaking coatings should be removed back to a firm edge. Low or high temperatures may require specific application techniques to achieve maximum film build.

When applying by methods other than airless spray, the required film build is unlikely to be achieved.

Typically this would apply to C or D grade rusting in this standard. A surface profile of mils microns is recommended. Be the first to write a review for this product!

Do not thin more than allowed by local environmental legislation. Press and move to zoom. Alternatively, a broadcast method of application can be used.

Sagola interesal Air texture gun fitted with a mm nozzle. Preferred application is by a suitable large tip hopper gun e. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal HS.

Dry bristle brushing will normally be adequate for accumulated dirt. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates.