INVERTER OMRON 3G3JX PDF

Notice: OMRON products are manufactured for use according to proper procedures .. You can install multiple 3G3JX inverters side by side in the control panel. Simple, Compact Inverters SYSDRIVE JX Series . Model name (3G3JX-) In no event shall the responsibility of OMRON for any act exceed the individual. Inverter 3G3JX . Use this terminal block to connect the inverter to the Sysmac® is a trademark or registered trademark of OMRON Corporation in Japan and.

Author: Faeramar Tagore
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Health and Food
Published (Last): 23 June 2016
Pages: 140
PDF File Size: 17.65 Mb
ePub File Size: 16.83 Mb
ISBN: 180-2-31424-592-3
Downloads: 11290
Price: Free* [*Free Regsitration Required]
Uploader: Taumi

This manual should be delivered to the actual end user of the product. In no event shall the responsibility omrn OMRON for any act exceed the individual price of the product on which liability is asserted.

At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. Performance data given in this manual is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Indications and Meanings of Safety Information In this user’s manual, the following precautions and signal words are used to provide information to ensure the safe use of the 3G3JX Inverter.

The information provided here is vital to safety. Strictly observe the precautions provided. Doing so might result in a small-scale fire, heat generation or damage to the unit.

Install a stop motion device to ensure safety. Not doing so might result in a minor injury. A holding brake is not a stop motion device designed to ensure safety. The material of the wall has to be nonflammable such as a metal plate. Precautions for Correct Use Warning Labels Warning labels are located on the Inverter as shown in inerter following illustration.

Be sure to follow the instructions. Should you find any problems with the product, immediately contact your nearest local invertfr representative or OMRON sales office. Understanding the following configuration ensures more effective use of the product. Overview Chapter 1 Overview Describes onron and names of parts. App-1 Appendix-2 Product Life Curve For factory maintenance only Communications connector Relay output terminal block Control circuit terminal block Main circuit terminal block output side S7: Not doing so may result in a serious injury due to an electric shock.

  CARA MEMIKAT WANITA IDAMAN ANDA RONALD FRANK PDF

Omron 3G3JX User Manual

Wiring work must be carried out only by qualified personnel. Install the Inverter on a nonflammable wall surface material, like metal. After completing the installation process, be sure to remove the imron from the Inverter before operation. Ventilation openings Both sides and top. Lift the bottom of the front cover to remove while holding the body. Loosen the front cover mounting screw. Hang the upper side on the inverrter. Connect securely to the ground as specified type-D grounding for V class, and type-C grounding for V class.

Do not share the grounding electrode with other strong electrical devices.

Example of incorrect grounding Example of correct grounding Inverter Inverter Inverter External power 3h3jx input At source logic PNP: Power supply output Note: By factory default, the input logic of the multi-function input terminal circuit is set to the sink logic. The default setting is sink logic.

When 3g3nx stopping the load with an MC on the primary side of the main circuit, however, the regenerative braking does not work and the load coasts to a stop free run. A general-purpose noise filter will be less effective and may not reduce noise. Connect a noise filter to the output side of the Inverter to reduce induction and radio noise.

Electromagnetic induction can generate noise on the signal line, causing the controller to malfunction.

If the cable length is increased, the stray capacitance between the Inverter outputs and the ground is increased proportionally. An increase in stray capacitance causes high-frequency leakage current to increase, affecting the current detector in the Inverter’s output unit and peripheral devices.

At source logic mA max. Contact The figure below illustrates the wiring of the sink logic. Below are the contact specifications of the relay output. Be sure to install it inside the control panel. Chapter 3 Operation Test Run Procedure Doing so may result in a serious injury due to an electric shock. Do not operate the Digital Operator or switches with wet hands.

OMRON 3G3JX USER MANUAL Pdf Download.

Key sequence Display example Description k0. Onverter key To change the set value, be sure to press the Enter key. Increment key Also, increases the set value of each function. Factory Default Operation Procedure Example: The data of the set monitor is displayed.

  LAPORAN PENDAHULUAN SELULITIS PDF

The code of the monitor mode is displayed as “d”. The code of the basic function mode is displayed as “F”. The extended function mode is displayed as “A”. Factory Default Change the A setting. The code of the monitor mode is displayed as “A”.

Change the function code. Factory Default “A” is displayed. Change the 1st digit of the function code. With this key, you can always change the display as follows. Data is not stored by pressing the Mode key. Press the Enter key to store the data. If a parameter for an extended function code is stored after pressing the Enter key, however, that code A, b, C, d, or H appears at the next power-on. FV input only FI input only A FV start frequency 0.

Manual torque boost only A upper limit frequency Frequency lower 0. Normal operation A selection Frequency matching start Trip after frequency matching deceleration stop Allowable b Disabled b selection Enabled in constant speed operation selection 1.

Disabled stop function at b Enabled Stop momentary power Enabled Restart interruption Starting voltage of non-stop function b 0. Disabled Free-run stop FW forward Multi-function RV reverse C input 1 selection CF1 multi-step speed setting binary omronn CF3 multi-step speed setting binary 3 C FA1 constant speed arrival signal Multi-function FA2 over set frequency arrival signal C output terminal P1 OL overload warning selection OD excessive PID deviation.

The monitor LED indicator “Hz” lights up omro d is displayed. Displays in increments of 0. Output Current Monitor [d] Displays the output current value of the Inverter.

C to C contact selection are excluded. Example Multi-function input terminals S4, S2: The monitor LED indicator “V” lights up. Displays in increments of 1 V. The most recent trip is displayed on trip monitor 1. For other methods, refer to the [A] section in “Frequency Reference Selection” Function name Data Default setting Unit Frequency reference Digital Operator F 2nd frequency Be careful, especially knverter you set a base frequency at below 50 Hz.

Otherwise, the motor may burn out.